High Evaporation Intensity Catfish Fish Feed Drying Equipment Heated By Steam 0.5 T/H
Fish feed dryer Introduction
Fish feed dryer is usually used in combination with fish feed cooler in the fish feed pellet line. Fish feed pellets are transported from fish feed extruder to the pellet dryer machine, then being conveyed on the mesh belt which is made of stainless steel.There is circulating fan, heating device, fresh-air-suction-system and exhaust-exiting system. Operator can take independent operational parameter control of temperature, humidity and exhaust gas re-circulation rate, which ensures the reliability of the fish feed pellet dryer, and the optimization of the operating conditions. Mesh-belt Type Fish Feed Dryer has good security and operation flexibility. The drying process is carried out in a fully-sealed box, effectively avoiding dust leakage. Damp materials are evenly spread on the mesh belt which is driven to move by transmission device in the dryer machine. From bottom to top, hot air flow through the mesh belt and fish feed pellets on it. In the drying process, heat exchange is sufficient & uniform, drying efficiency being extremely high.
Operation and Maintenance of Fish Feed Dryer
Head of the machine
The machine head is composed of two driven rollers, tightener, feed inlet and outlet.
Passive bearing bears the tension and determines the tightness of the mesh belt, so bearings at both ends of the passive rollers should be regularly lubricated with high temperature (above 200℃) lubricating grease, to ensure the normal operation of the dryer.
Tightener is to adjust the mesh belt tightness. The first installation, mesh belt should be tightened, and after heating up, tightening again (because of the thermal expansion).
Drying section
This stage is the actual working area of material drying, blast pipe and discharge pipe being installed on the top. Hot air flows into the underpart of the inner chamber from both sides, then extracted out by wind turbine from the middle. There are control valves being installed on the air inlet and outlet to adjust air velocity.
Dryer end
The transmission part is installed in the end of the fish feed pellet dryer. The tightness of the transmission chain can be adjusted by adjusting the position of the gear reducer. Transmitting gear on the other side of the gear reducer will also inject lubricating oil to extend its service life.
Advantages of Mesh Belt Fish Feed Dryer
◆ High-efficiency and energy saving
◆ Easy to install and maintain
◆ Fast drying speed, high evaporation intensity
◆ Convenient drying parameters adjustment, flexible operation, wide adaptation
◆ Higher work capacity, the range of drying time is adjustable
◆ Standardized production, users can increase the number of segments according to production
Technical Parameter
| Model | Heating Powder | Mesh belt power | Exhaust wind power | Circulating fan power | Capacity | Dimension | Weight |
| SW-150 | Heating power: 15-18kw (can also be heated by steam, the required steam volume is 0.1t/h) | 1.5kw | 0.37kw | 0.15kw | 150-200 | 3200*1100*1550mm | 580kg |
| SW-300 | Heating power: 24kw
(can also be heated by steam, the required steam volume is 0.1t/h) | 2.2kw | 0.55kw | 0.15kw | 200-300 | 3200*1200*1850mm | 750kg |
| SW-500 | Heating power: 26-28kw
(can also be heated by steam, the required steam volume is 0.1-0.2t/h) | 4.0kw | 0.75kw | 0.37kw | 500-600 | 5000*1650*2150mm | 1200kg |
| SW-1000 | Heating power: 30kw
(can also be heated by steam, the required steam volume is 0.2-0.3t/h) | 5.5kw | 1.1kw | 0.55kw | 1000-2000 | 4100*1600*2200mm | 2400kg |
| SW-2000 | Heating power: 45kw
(can also be heated by steam, the required steam volume is 0.5t/h) | 5.5kw | 1.5kw | 0.55kw | 2000-2500kg/h | 6500*2100*2400mm | 3200kg |
Product Tags:
|
|
Catfish Fish Feed Dryer Equipment Steam Heated 0.5 T/H High Evaporation Intensity Images
|
